Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
| Параметр | Значение |
| Общие характеристики | |
| Артикул | 68196 |
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Degree of protection | IP54 according to EN 60529 |
| Connection | Insulation piercing technology Yellow flat cable/black flat cable M8 round plug connector in accordance with EN 61076-2-104 LF004-GS1-A (4-pin, bushing contacts, screw lock, A-coded) Matching connector: LM004-Gx1-A or similar NF005-SS1-B (5-pin, bushing contacts, snap lock, B-coded). Matching connector: NM005-Sx1-B or similar |
| Mass | 220 g |
| Switching point | according to DIN EN 61131-2 0 (undamped) ≤ 0.5 mA 1 (damped) ≥ 2.0 mA |
| Mounting | 2 clips with ∅ 8 mm drill hole |
| Current | max. 5 A per motor |
| Note | The flat cable routing is designed for 100 actuation cycles |
| Cable length | 1 m |
| Rated operating current | ≤ 35 mA |
| Emitted interference | EN 61000-6-4:2007 |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Directive 2014/30/EU | EN 62026-2:2013 |
| Supply | from external auxiliary voltage U |
| Fieldbus standard | EN 62026-2:2013 |
| LED ERR | Motor fault: 2 LED yellow |
| LED PWR | AS-Interface voltage; green LED green: voltage OK green flashing: address 0 or sensor supply overload or speed signal overload or external auxiliary voltage U missing |
| Current loading capacity | 500 mA , overload and short-circuit protected |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| UL File Number | E223772 "For use in NFPA 79 Applications only" |
| Number/Type | 2 outputs for DC roller motors (MOT1, MOT2) |
| Signal delay | < 1 ms (input/AS-Interface) |
| Input current | ≤ 8 mA (limited internally) |
| AS-Interface specification | V3.0 |
| LED AUX | ext. auxiliary voltage U ; dual LED green/red green: voltage OK red: reverse voltage |
| AS-Interface | EN 62026-2:2013 |
| MTBF | 98 a |
| Slave type | A/B slave |
| Required master specification | ≥ V2.1 |
| LED IN | switching state (input); 2 LED yellow |
| Input | EN 61131-2:2007 |
| Profile | S-7.A.E |
| IO code | 7 |
| ID code | A |
| ID1 code | 6 |
| ID2 code | E |
| D0 | MOT1 fault MOT1 operation |
| D1 | MOT2 fault MOT2 operation |
| D2 | IN1 MOT1/MOT2 rotation direction |
| D3 | IN2 - |
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of sensor supply or speed signal overload or external auxiliary voltage U missing |
| Auxiliary voltage (output) | 18 ... 30 VDC PELV |
| Compatible roller motors | Interroll EC310, Rulmeca BL3 |
| LED MOT | Motor active; 2 yellow LEDs |
| Input filter | 2 ms |
| Overload protection | fuse , I t = 53.7 A s |
| Velocity signal | 1.4 … 13 V at no-load R = 5.6 kΩ, R ≥ 35 kΩ Control via parameter P2:0 |
| Rotation direction signal | Off / ≥ (U - 1.0 V) at no-load R = 5.6 kΩ, R ≥ 5 kΩ AS-Interface data bit D2 = 0: U = Off |
| Motor fault | Digital input NPN, U = 3.3 V, R = 52 kΩ 0 (no error) ≥ 40 µA 1 (error) ≤ 30 µA |
| LED FUSE | Motor power supply; 2 green LEDs |
| LED DIR | Motor rotation direction; yellow LED |
Сравнение
Избранное
