Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
| Параметр | Значение |
| Общие характеристики | |
| Артикул | 74956 |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Degree of protection | IP20 |
| Connection | Removable push-in terminals rated connection capacity: rigid: 0.20 mm ... 1.5 mm flexible (without wire end ferrule): 0.20 mm ... 2.5 mm flexible (with wire end ferrule): 0.25 mm ... 1.5 mm |
| Housing | PA 66-FR |
| Mass | 110 g |
| Relative humidity | 85 % , noncondensing |
| Altitude | ≤ 2000 m above MSL |
| Mounting | DIN mounting rail |
| Protection class | III |
| Note | Max. length of jumpers = 5 cm |
| Resolution | Voltage output: 3 mV Current output: 6 µA |
| Pollution degree | 2 |
| Temperature influence | 1 µA/K or 0,3 mV/K |
| Vibration resistance | 0.35 mm 10 ... 57 Hz , 5 g 57 ... 150 Hz, 20 cycles |
| Shock and impact resistance | 15 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks |
| Rated operating current | ≤ 75 mA |
| Emitted interference | EN 61000-6-4:2007 |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Directive 2014/30/EU | EN 62026-2:2013 |
| Supply | From auxiliary voltage U |
| Accuracy | 0.15 % of full-scale value |
| Fieldbus standard | EN 62026-2:2013 |
| Short-circuit current | voltage output: max. 22 mA |
| LED PWR | AS-Interface voltage; green LED Green: voltage OK Flashing green: address 0 or peripheral error |
| Climatic conditions | For indoor use only |
| Current consumption | I ≤ 650 mA |
| Current loading capacity | ≤ 600 mA (signal current + actuator power supply) from external auxiliary voltage U , overload-proof and short-circuit proof |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| UL File Number | E223772 |
| Number/Type | Two analog outputs Current: 0 mA ... 20 mA Voltage: 0 V ... 10 V |
| Surge protection | U , U : overvoltage category II, safe isolated power supplies (PELV) |
| AS-Interface specification | V3.0 |
| LED AUX | ext. auxiliary voltage U ; dual LED green/red green: voltage OK red: reverse voltage |
| AS-Interface | EN 62026-2:2013 |
| MTBF | 197 a |
| Slave type | Standard slave |
| Required master specification | ≥ V2.1 |
| Profile | S-7.3.5 |
| IO code | 7 |
| ID code | 3 |
| ID1 code | F |
| ID2 code | 5 |
| P0 | Watchdog: P0=1 (default), watchdog active P0=0, watchdog inactive |
| P1 | Output mode O1: P1=1 (default), current output P1=0, voltage output |
| P2 | Indication of peripheral fault: P2=1 (default), peripheral fault is reported P2=0, peripheral fault is not reported |
| P3 | Output mode O2: P3=1 (default), current output P3=0, voltage output |
| LED FAULT | Fault indication: red LED Red: communication error or address is 0 Red flashing: peripheral fault |
| Auxiliary voltage (output) | 24 V DC ± 15 % PELV |
| Load | voltage output: min. 1 kΩ current output: max. 600 Ω |
| (function via AS-Interface) | The transfer of the data value is based on AS-Interface Profile 7.3. |
| LED OUT | Status of output signal; yellow LED Yellow: output value within value range Continually on: current mode 1.4 s on/0.1 s off: voltage mode Flashing yellow: wire break (at current output) or output value outside of value range |
Сравнение
Избранное
