Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
Параметр | Значение |
Общие характеристики | |
Артикул | 43210 |
Control elements | DIP-switch |
Ripple | within the supply tolerance |
Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) |
Degree of protection | IP20 |
Connection | SL1: 6b |
Mass | approx. 100 g |
Rated voltage | 20 ... 30 V DC bus powered via Termination Board |
Electromagnetic compatibility | NE 21:2006 For further information see system description. |
Mounting | on Termination Board |
Current | 2.4 mA |
Marking | II 3G Ex nA II T4 |
Output type | open collector transistor (internal fault bus) |
Dimensions | 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 inch) |
Labeling | space for labeling at the front |
EU-type examination certificate | BASEEFA 10 ATEX 0031X |
IECEx approval | IECEx BAS 10.0012X IECEx BAS 10.0013X |
Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Approved for | [Zone 0] [Ex ia] IIC, [Ex iaD], [Ex ia] I Ex nA II T4 |
Power | 3.3 mW |
Rated current | ≤ 22 mA |
Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
Certificate | BASEEFA 10 ATEX 0032X |
Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
Display elements | LEDs |
Configuration | via DIP switches |
Control drawing | 116-0317 (cULus) |
Voltage | 5.5 V DC |
Maximum safe voltage | 253 V (Attention! The rated voltage can be lower.) |
Connection side | control side |
Load | Accuracy figures for infinite load impedance. Additional 0.03 % of span for a load resistance of 10 kΩ |
Input resistance | ≥ 16 MΩ |
Input/Output | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
Line fault detection | input: ± 100 mV output: +200 mV, -115 mV |
Signal type | Analog input |
Input/power supply | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
Output/power supply | functional insulation, rated insulation voltage 50 V AC |
Influence of ambient temperature | ± 1 µV/K (typical ± 0.25 µV/K) |
Protection against electrical shock | UL 61010-1 |
Power dissipation/power consumption | 0.7 W max. |
Coding | pin 2, 3 and 4 trimmed For further information see system description. |
After calibration | at 20 °C (68 °F): ± 3 µV up to ± 10mV/± 0.05 % of the span up to +50 mV/± 0.05 % of the span up to -50 mV |
Bandwidth | DC to > 350 Hz (-3 dB) |
Output resistance | max. 3 Ω |
Transmission range | 0 ... ± 50 mV |
Settling time | < 2 ms |
Rise time/fall time | ≤ 1 ms |
Offset voltage/current | ≤ 5 µV / ≤ 5 nA |
Absolute | < 0.25 K at 30 V voltage supply |
Fault voltage | < V /2 (when connected to V via 10 kΩ pull up resistor) |
Lockout voltage | > 11 V DC |