Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
| Параметр | Значение |
| Общие характеристики | |
| Артикул | 58506 |
| MTTF | 200 a |
| UL approval | An isolated source with a secondary open circuit voltage of ≤ 30 V with a 3 A maximum over current protection. Over current protection is not required when a Class 2 source is employed. UL mark does not provide UL certification for any functional safety rating or aspects of the device. |
| Ambient temperature | 0 ... 55 °C (32 ... 131 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Degree of protection | IP20 |
| Housing | Stainless steel |
| Mass | 800 g |
| Electromagnetic compatibility | EN 61000-6-2:2005, EN 61000-6-4:2007 |
| Construction type | Low profile housing , Stainless steel |
| Interface type | Chip card slot |
| Transfer rate | 10 MBit/s |
| Protocol | EtherNet/IP + MODBUS TCP/IP acc. to IEEE 802.3 supports device level ring protocol DLR |
| B | 2 E+7 |
| Standards | EN 61000-6-2:2005, EN 61000-6-4:2007 EN 61326-3-1:2008 IEC 61508:2010 and EN 62061:2005 (up to SIL3) EN 13849:2008 (PL e) |
| Response delay | < 40 ms |
| Rated operating current | ≤ 300 mA from AS-Interface |
| Switch-on delay | < 10 s |
| Directive 2014/30/EU | EN 62026-2:2013 EN 61000-6-2:2005, EN 61000-6-4:2007 |
| Shock resistance | EN 61131-2:2004 |
| Safety Integrity Level (SIL) | SIL 3 |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface; Output K3 and K4 24 V |
| UL File Number | E223772 only from low voltage, limited energy source (SELV or PELV) or listed Class 2 source |
| Number/Type | 4 EDM/Start inputs: EDM: Inputs for the external device monitoring circuits Start: start inputs: Static switching current 4 mA at 24 V, dynamic 30 mA at 24 V (T=100 μs) |
| Performance level (PL) | PL e |
| Safety output | Output circuits 1 and 2: 2 potential-free contacts, max. contact load: 3 A at 30 V , 3 A at 30 V Output circuits 3 and 4: 2 PNP transistor outputs max. contact load: 0.5 A at 30 V |
| Button | 4 |
| AS-Interface specification | V3.0 |
| PLC-Functionality | activateable |
| Duplicate address detection | from AS-Interface slaves |
| Earth fault detection | integrated |
| EMC monitoring | integrated |
| Diagnostics function | Extended function via display |
| Display | Illuminated graphical LC display for addressing and error messages |
| LED ETHERNET | ethernet active; LED green |
| LED AS-i ACTIVE | AS-Interface operation normal; LED green |
| LED CONFIG ERR | configuration error; LED red |
| LED PRG ENABLE | autom. programming; LED green |
| LED POWER | voltage ON; LED green |
| LED PRJ MODE | projecting mode active; LED yellow |
| LED U AS-i | AS-Interface voltage; LED green |
| LED AUX | ext. auxiliary voltage U ; LED green |
| LED EDM/Start | External device monitoring circuit inputs closed, 4x yellow LEDs |
| LED output circuit | Output circuit closed; 4 x green LEDs |
| Insulation voltage | ≥ 500 V |
| Ethernet | RJ-45 |
| AS-Interface | EN 62026-2:2013 |
| Switch SET | Selection and setting of a slave address |
| OK button | Mode selection traditional-graphical/confirmation |
| Button MODE | Mode selection PRJ-operation/save configuration/cursor |
| ESC button | Mode selection traditional-graphical/cancel |
| Data decoupling | integrated |
| Directive 2006/42/EC | EN 61508-1:2010 EN/ISO 13849-1:2008 EN 62061:2005 |
Сравнение
Избранное
