Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
| Параметр | Значение |
| Общие характеристики | |
| Артикул | 64983 |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Degree of protection | housing: IP67 IP67 / IP68 / IP69K with flat cable VAZ-FK-S-* M12 socket: IP69K |
| Connection | AS-Interface/U : AS-Interface flat cable Inputs/outputs: M12 round connector, 4-pin, A-coded, according to IEC 61076-2-101:2012 WAGO terminal type 733-105 |
| Housing | PBT PC |
| Mass | 100 g |
| Switching point | according to DIN EN 61131-2 (Type 2) |
| Protection class | III |
| Contacts | M12: CuSn/Au WAGO terminal: CrNi |
| Body | black PUR |
| Cable | PUR |
| Sheath diameter | ∅4,3 mm |
| Color | black |
| Cores | 0.34 mm |
| Length | 1 m |
| Vibration resistance | 0.75 mm 10 ... 57 Hz , 5 g 57 ... 150 Hz, 20 cycles |
| Shock and impact resistance | 30 , 11 ms in 6 spatial directions 3 shocks 10 , 16 ms in 6 spatial directions 1000 shocks |
| Tightening torque, fastening screws | 1.65 Nm |
| Rated operating current | ≤ 40 mA / max. 60 mA |
| Emitted interference | EN 61000-6-4:2007/A1:2011 |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Directive 2014/30/EU | EN 62026-2:2013 |
| Supply | from external auxiliary voltage U |
| Fieldbus standard | EN 62026-2:2013 |
| Voltage | ≥ (U - 0.5 V) |
| Mounting screw | Stainless steel 1.4305 / AISI 303 |
| Current loading capacity | ≤ 1000 mA overload and short-circuit resistant |
| Rated operating voltage | 18.5 ... 31.6 V from AS-Interface |
| Number/Type | 1 electronic output, PNP, |
| Surge protection | U , U : Over voltage category III, safe isolated power supplies (PELV) |
| Signal delay | < 1 ms (input/AS-Interface) |
| Input current | ≤ 9 mA (limited internally) |
| AS-Interface specification | V3.0 |
| AS-Interface | EN 62026-2:2013 |
| Slave type | A/B slave |
| Required master specification | ≥ V2.1 |
| LED IN | switching state (input); 2 LED yellow |
| 0 (unattenuated) | ≤ 3 mA |
| 1 (attenuated) | ≥ 5 mA |
| Input | EN 61131-2:2007 |
| Profile | S-7.A.E |
| IO code | 7 |
| ID code | A |
| ID1 code | 7 |
| ID2 code | E |
| D0 | IN1 O1 |
| D1 | IN2 - |
| D2 | - - |
| D3 | - - |
| P0 | communication monitoring P0 = 1 (default settings), monitoring = ON, i.e. if communication fails, the outputs are de-energised P0 = 0, monitoring = OFF, if communication fails, the outputs maintain their condition |
| P1 | Input filter P1 = 0 input filter on, pulse suppression ≤ 2 ms P1 = 1 input filter off (default settings) |
| P2 | Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings) |
| P3 | not used |
| Tightening torque, cable gland | 0.4 Nm |
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of sensor power supply or overload of outputs or external auxiliary voltage U missing |
| LED AS-i | AS-Interface voltage; LED green |
| LED OUT | Switching state (output); LED yellow |
| Auxiliary voltage | 20 ... 30 V DC PELV |
Сравнение
Избранное
