Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
| Параметр | Значение |
| Общие характеристики | |
| Артикул | 47255 |
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Degree of protection | IP20 |
| Connection | removable terminals rated connection capacity: rigid/flexible (with and without wire-end ferrules): 0.25 mm ... 2.5 mm for multiple-wire connection with two wires of equal cross-section: flexible with twin wire-end ferrules: 0.5 mm ... 1.5 mm |
| Housing | PA 66-FR |
| Mass | 150 g |
| Switching point | according to DIN EN 61131-2 (Type 2) |
| Relative humidity | 85 % , noncondensing |
| Altitude | ≤ 2000 m above MSL |
| Mounting | DIN mounting rail |
| Protection class | III |
| Pollution degree | 2 |
| Rated operating current | ≤ 30 mA (without sensors) / max. 180 mA |
| Emitted interference | EN 61000-6-4:2007 |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Directive 2014/30/EU | EN 62026-2:2013 EN 61000-6-2:2005, EN 61000-6-4:2007 |
| Supply | from AS-Interface (switch position INT, default settings) or external U (switch position EXT) |
| Fieldbus standard | EN 62026-2:2013 |
| LED PWR | AS-Interface voltage; green LED green: voltage OK flashing green: address 0 |
| Voltage | 21 ... 31 V DC (INT) |
| Climatic conditions | For indoor use only |
| Current loading capacity | ≤ 150 mA, overload- and short-circuit protected (INT) |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| UL File Number | E223772 |
| Number/Type | 4 inputs for 2- or 3-wire sensors (PNP), DC |
| Surge protection | U , U : Over voltage category III, safe isolated power supplies (PELV) |
| Signal delay | < 1 ms (input/AS-Interface) |
| Input current | ≤ 9 mA (limited internally) |
| Tightening torque of clamping screws | 0.5 Nm ... 0.6 Nm |
| AS-Interface specification | V3.0 |
| AS-Interface | EN 62026-2:2013 |
| Slave type | A/B slave |
| Required master specification | ≥ V2.0 |
| LED IN | switching state (input); 4 LED yellow |
| 0 (unattenuated) | ≤ 3 mA |
| 1 (attenuated) | ≥ 5 mA |
| Input | EN 61131-2:2004 |
| Profile | S-0.A.0 |
| IO code | 0 |
| ID code | A |
| ID1 code | 7 |
| ID2 code | 0 |
| D0 | IN1 |
| D1 | IN2 |
| D2 | IN3 |
| D3 | IN4 |
| P0 | not used |
| P1 | Input filter P1 = 0 input filter on, pulse suppression ≤ 2 ms P1 = 1 input filter off (default settings) |
| P2 | Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings) |
| P3 | not used |
| LED FAULT | Fault display; Red LED red: Communication fault or address is 0 red, flashing: Overload, internal input supply |
| LED INT | Internal input supply active; LED green |
| Auxiliary voltage (input) | 12 ... 30 V DC PELV |
Сравнение
Избранное
