Для оформления заявки добавьте оборудование
в корзину и сформируйте заказ
Доставка в любой регион России транспортной
компанией на Ваш выбор
| Параметр | Значение |
| Общие характеристики | |
| Артикул | 81807 |
| Operating voltage | 10 ... 30 V DC , ripple 10 % |
| No-load supply current | ≤ 50 mA |
| Repeat accuracy | ≤ 0.1 % of full-scale value |
| Switching frequency | ≤ 14 Hz |
| UL approval | cULus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
| Degree of protection | IP67 |
| Housing | PA-GF35 |
| Mass | 345 g |
| Interface type | Serial interface (programming adapter required) 9600 BPS, no parity, 8 data bits, 1 stop bit |
| Voltage drop | ≤ 2 V |
| Pulse length | 0.5 ... 300 ms (level 1) |
| Cable | PUR |
| Sheath diameter | 7.25 mm |
| Bending radius | > 37.3 mm , fixed > 74.7 mm , moving |
| Length | 2 m |
| Temperature influence | < 1.5 % of full-scale value |
| Output type | 2 switch outputs NPN, NO/NC, programmable |
| Connection type | cable , 5-pin |
| Standards | EN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 |
| Core cross-section | 5 x 0.82 mm |
| LED green | Operating display |
| Input/output type | 1 synchronization connection, bidirectional |
| EAC conformity | TR CU 020/2011 |
| Supplementary information | Switch settings of the external programming adapter: "output load": pull-up "output logic": inv |
| Adjustment range | 50 ... 500 mm |
| Sensing range | 35 ... 500 mm |
| Dead band | 0 ... 35 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 380 kHz |
| Response delay | minimum : 20 ms factory setting: 55 ms |
| LED red | error |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Rated operating current | 200 mA , short-circuit/overload protected |
| Range hysteresis | programmable , preset to 1 mm |
| Output rated operating current | < 12 mA |
| Level | 4 V ... U |
| Input impedance | > 12 kΩ |
| Output 1 | near switch point: 50 mm far switch point: 500 mm Output mode: Window mode output behavior: NO contact |
| Output 2 | near switch point: 100 mm far switch point: 250 mm Output mode: Window mode output behavior: NO contact |
| Beam width | wide |
| Common mode operation | ≤ 70 Hz |
| Multiplex operation | ≤ 90 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ) |
| LED yellow 1 | switching state switch output 1 |
| LED yellow 2 | switching state switch output 2 |
| Pulse interval | ≥ 14 ms (level 0) |
| Evaluation procedure | averaging (MxN) M = 5 N = 2 |
Сравнение
Избранное
